Floor Sealers In Ludhiana

MOQ5 Liter/Liters

ColorTransparent

ApplicationApply using a brush roller cloth sponge or sprayer. Buffs dry and excess sealer that does not penetrate within 3 to 5 minutes with an absorbent trowel or carpet bonnet. Highly porous surfaces may require a second or third application to give full protection. wait a minimum of 1 hour between applications. May be opened for foot traffic in 2 hours. Achieves a full cure in 24 hours.

Physical StateLiquid

Product DescriptionWe hold immense pleasure in introducing ourself as one one of the leading manufacturers and suppliers of a wide range of Floor Coatings . These products are commonly applied on concrete floors to prevent from different damages caused by water and other substances. Offered coatings are widely appr

Product DescriptionOur company is manufacturing and supplying a wide range of Floor Sealers. This is one of the most demanded brands which are specially designed for polishing marbles granites and other exterior surfaces. It is a solvent based liquid and widely used to prevent stains and also provide repellent effect

Product DescriptionWe are a leading manufacturer and supplier of Epoxy Floor Sealer from Vapi Gujarat India. Being created out of the very best raw content and today's technological innovation the provided Epoxy Floor Sealer is extremely appreciated by our customers for its performance appearance and durability.

MOQ10 Kilograms/Kilograms

ApplicationOn application of diluted solution Liquid Sealer reacts with air to form active resins in pores which prevent penetration of liquid.

GradeIndustrial

HS Code39100090

Type100 % Silane / siloxane

Chemical NameSilane/Siloxane

UsageTreated surfaces resist liquid penetration without significantly reducing breath-ability of the surface.

Product DescriptionFloor Coatings & Sealers

Product DescriptionOur esteemed organization is well known for providing Clear Coatings for Floors Concrete Sealers that are designed and developed for cement based material and concrete structures. Moreover these help in self polishing of the surface instead of eroding. Customers can avail these at affordable rates

MOQ10 Liter/Liters

ApplicationApply using a brush roller cloth sponge or sprayer. Buffs dry any excess sealer that does not penetrate within 3 to 5 minutes with an absorbent trowel or carpet bonnet. Highly porous surfaces may require a second or third application to give full protection. Wait a minimum of 1 hour between applications. May be opened for foot traffic in 2 hours. Achieves a full cure in 24 hours.

Colorcoloureless

Physical StateLiquid

MOQ10 Liter/Liters

ApplicationApply on the surface a thin layer of product with a soft bristle brush or with a lambs wool and let it dry 6-8 hours. take the residue away by means of a fine pad polishing machine.

Colorcolourless

Physical StateLiquid

MOQ5 Liter/Liters

ColorTransparent

ApplicationApply on the dry and clean surface a thin even layer of STONE SEAL by means of a brush lambs wool or low pressure sprayer. Two coats wet are required only on the most absorbing materials. Allow to dry completely. For polished materials remove the dull patina with steel wool pad or with a cloth slightly damp with STONE SEAL. For large surfaces use a floor machine with red pad or fine steel wool pad. The surface can be opened to foot traffic 3-6 hours after treatment; however it must not be wet for the next 24 hours i.e. until the product has completely hardened.

Physical StateLiquid

MOQ5 Liter/Liters

ColorTransparent

ApplicationSpread a thin even layer of PORO SEAL by means of a soft brush or lambs wool or low pressure sprayer. On the most absorbent stones two applications may be required. Wait 2-3 hours between each coat. Surface to be treated has to be completely dry and clean.

Physical StateLiquid

MOQ5 Liter/Liters

ColorTransparent

Physical StateLiquid

MOQ5 Liter/Liters

ApplicationGrout joints must be clean dry and free of existing sealers and coating to ensure good bonding. Apply 2 coats with a soft-bristle paint brush. Allow a minimum of 30 minutes drying times between coats. Sealed area should be kept dry for 12 hours. Achieves a full cure in 24 hours. Use cotton or paper towels polish dry any sealer remaining on the tile and grout within 3 to 5 minutes of application. Do not allow sealer to come in contact with any non-recommended surface.

ColorTransparent

Physical StateLiquid

Product DescriptionSealer for sidelaps endlaps and self-glashing windows shall be tape of low hardening permanently flexible blend of butyl rubber. Sealers secure the surface by putting a stain repellent hurdle between the pollute and the stone tile and grout allowing response time to clean the surface. Nominal pri