Uv Glass Adhesive In Dombivli

MOQ5 Liter/Liters

Adhesive TypeWater Activated

UsageConstruction

ApplicationIncrease Adhesion of Tiles Improve Flexibility Reduces Water Permeability Widen Application.

ColorWhite

Physical StateLiquid

MOQ5 Pack/Packs

ColorWhite

Adhesive Typesolvent adhesive

UsageConstruction

ApplicationPrepare Pinnacle in a clean container first of all pouring in a quantity of water equal to approximately . of that which will be required. Gradually add Pinnacle to the water in the container mixing the paste from the bottom upwards with a low-rev ( 400 RPM /min.) helicoidal agitator. Then add more water until the desired consistency is obtainedthe mixture must be homogeneous and without any lumps. For best results and to mix larger quantities of adhesive a stirring device with vertical blades and slow rotation is recommended. Always use appropriate size of trowell with respect to the tile size and the density of the tile.Spread the adhesive over a surface area which will allow for laying of the surface materials within the indicated open time and check for suitability of the adhesive at regular intervals the open time may vary considerably during the same operation depending on various factors such as exposure to sunlight air currents absorbency of the substrate temperature and relative humidity of the atmosphere.Press down each tile to allow for complete uniform contact with the adhesive. In the case of laying in environments subject to heavy traffic or in outdoor locations the double-spread technique must be used to ensure 100% coverage of the rear of the tiles.

Physical StatePowder

MOQ5 Pack/Packs

ColorWhite

UsageConstruction

ApplicationFixing absorent floor and wall tiles outdoors and indoors. The tiles can be made of : cotta double- fired single fired ceramic.Fixing natural stone and marble so long as they are not affected by water.Fixing on heating floors.Fixing poorly absorbent or non-absorbent materials such as single-fired tiles refined porcelain stoneware and vitrified tiles.Spot-gluing insulating panels made of polystyrene polyurethane foam rock or glass wool.Suitable for fixing tiles: on top of old ceramic tiles or on facadesVery good for large format paving slabs.

Physical StatePowder

MOQ10 Kilograms/Kilograms

ColorLight Grey

ApplicationDesigned for ceramic floor and wall tiles for oudoor and indoor. The tiles can be make of Cotto Double Fire Single Fire Ceramic

Physical StatePowder

MOQ5 Pack/Packs

ColorLight Grey

Adhesive TypeWater Activated

ApplicationDesigned for ceramic floor and wall tiles for outdoor and indoor. The tiles can be make of Cotto Double Fire Single Fire ceramic.

Physical StatePowder

MOQ5 Pack/Packs

ColorWhite & Grey

Adhesive TypeWater Activated

UsageConstruction

ApplicationFixing ceramic tiles of all types to difficult substrates or ones liable to considerably warp.Fixing natural stone sensitive to humidity composite marble.For fixing vitreous mosaic.Fixing ceramic tiles to kitchen surfaces or work tops to wood glass or iron surfacesLaying on heating screeds.

Physical StateLiquid

MOQ5 Kilograms/Kilograms

Colorwhite

UsageConstruction

ApplicationWaterprooofing the walls and floors of swimming pools bathrooms or places where there is alot of moisture before the laying of ceramic wall tiles. Waterproofing terraces balconies prior to fixing ceramic tiles. Particularly suitable for raised floors.Restoring the waterproofing properties to old terraces without demolishing the existing floor surface. Leveling cracked plaster or concrete.

Physical StatePowder

MOQ5 Pack/Packs

Adhesive TypeWater Activated

UsageConstruction

ApplicationIncrease adhesion of tiles. Improve flexibility. Reduces water permeability. Widen application.

ColorWhite

Physical StateLiquid

MOQ5 Pack/Packs

Physical StatePowder

MOQ5 Pack/Packs

Adhesive Typesolvent adhesive

UsageConstruction

ApplicationDesigned for interior & exterior floor & wall installation of all types of glass mosaic. Very good for swimming pools and various water body. It can be used to clad glass tiles and natural stones/artificial stones.

ColorWhite

Physical StatePowder

MOQ5 Pack/Packs

Adhesive Typesolvent adhesive

UsageConstruction

ApplicationAdhesive slurry specially made for cement mortar bed fixing all kind of poorly absorbent floor or non-absorbent floor.

ColorGrey

Physical StatePowder

MOQ10 Pack/Packs

ColorGrey

Adhesive Typesolvent adhesive

UsageConstruction

ApplicationDesigned for ceramic floor and wall tiles for outdoor and indoor. The tiles can be make of Cotto Double fire Single Fire ceramic.

Physical StatePowder

MOQ5 Dram/Drams

ColorWhite

Adhesive Typesolvent adhesive

UsageConstruction

ApplicationThixotropic adhesive specially designed for requiring high elasticity adhesion and for stability with thermal shock with UV resistance.

Physical StateLiquid

MOQ5 Pack/Packs

Adhesive TypeWater Activated

ColorWhite & Grey

UsageConstruction

ApplicationFixing ceramic tiles of all types of difficult substrates or ones liable to considerably wrap. Fixing natural stones sensitive to humidity composite marble. For fixing vitreous mosaic. Fixing ceramic tiles to kitchen surfaces or work tops to wood glass or iron surfaces. Laying on heating screeds.

Physical StateLiquid

MOQ10 Pack/Packs

Adhesive Typesolvent adhesive

ColorWhite

UsageConstruction

ApplicationSpecially designed for interior & exterior floor and wall installation of all types of glass mosaic swimming pools various water body. It can be used to clad glass tiles and natural stones/ artificial stones.

Physical StatePowder