Ht Cable Jointing Kit In Mumbai

FeaturesHigh voltage Corrosion resistant Weatherproof Low maintenance Durable Safe operation Reliable performance Long lifespan

MOQ1 Piece/Pieces

Usage & ApplicationsCable entry into junction boxes connection boxes panels bulkheads and enclosures

Install TypeHot-air gun or propane torch; heat from the cable side not on the nut

Operating Temperature-40 to +110 deg C (continuous)

Tensile Strength12 N/mm2 min (ASTM D638)

Product TypeHeat-shrinkable cable gland / cable entry seal single outlet

Rated Voltage600 V (Gala catalogue rating)

FeaturesWeatherproof Easy Install Cost-effective Durable Corrosion resistant Environmentally friendly High performance Reliable Safe Long lasting

Tensile Strength12 N/mm2 min (ASTM D638)

Operating Temperature-40 to +100 deg C (continuous)

Install TypeShrunk over the outer sheath with a gas torch

Usage & ApplicationsSealing both ends of HV and EHV cable drums while venting evolved gas

Product TypeHeat-shrinkable cable end cap with non-return pressure relief valve

MaterialCross-linked polyolefin cap; brass-and-steel valve

MOQ1 Piece/Pieces

Install TypePush on by hand; no tools or heat

Thermal ConductivityLow thermal conductivity

Installation GuidelineSlide over cable end and heat for proper fit

Surface TreatmentSmooth surface finish

LayerSingle layer

Usage & ApplicationsTemporary protection of cable ends pipe ends tube ends and parts against weather moisture and contamination

FeaturesHigh-temperature Water-resistant Non-shrinkable Easy application Durable Corrosion resistant Weatherproof Conformable Heat resistant

MOQ1 Piece/Pieces

Install TypeWrap close the overlap shrink with a gas torch from the centre outwards until adhesive appears at the ends

Usage & ApplicationsRepair of damaged cable sheaths and protection of existing connections without cutting the cable

Product TypeHeat shrink cable repair sleeve wraparound adhesive lined

MaterialCross-linked polyolefin backing with hot-melt adhesive layer

ColorBlack

Size9 sizes GMRS-19 to GMRS-250 for cable OD 5 to 192 mm

MOQ1 Piece/Pieces

Operating Temperature-20 to +90 degC (service temperature Gala typical value black and red)

Install TypeCold applied; peel off the liner and press or wrap into place

Usage & ApplicationsWater sealing and void filling in heat shrink cable joints and terminations lugs breakouts and connectors; telecom sealing (black)

Product TypeMastic sealing tape (cold-applied) strips and rolls

MaterialButyl rubber based mastic sealant on silicone-coated paper liner

ColorBlack (HBMT) red (HRMT) yellow (HSCM)

MOQ1 Piece/Pieces

Install TypePropane or butane torch closed end first

Usage & ApplicationsSealing and identifying cable drum ends for cable-length warranty control

Operating Temperature-40 to +100 deg C (continuous)

Product TypeHeat-shrink cable end cap with customer logo printing (tamper-evident)

MaterialCross-linked polyolefin

ColorBlack with printed marking

MOQ1 Piece/Pieces

Install TypeUsually factory fitted; site fitting with propane or butane torch

Usage & ApplicationsPulling power and telecom cables into ducts and trenches while sealing the cable end

Product TypeHeat-shrinkable cable end cap with steel pulling eye

ColorBlack

MaterialCross-linked polyolefin cap steel pulling eye

SizeGEC 301L-PE to GEC 701L-PE cable outside diameter 28 to 112 mm

MOQ100 Piece/Pieces

Install TypeWound over the earth braid on the screen or armour by hand; no soldering

Usage & ApplicationsClamping earth braids or wires onto cable screens and armour in MV joints and terminations

Product TypeConstant force (roll) spring for solderless earth connections on cable screens and armour

MaterialStainless steel (per Gala sheet)

FeaturesReusable Insulated Durable Weatherproof Corrosion resistant Easy installation Cost effective Reduced downtime

MOQ1 Piece/Pieces

Install TypeScrewdriver or nut driver; adjustable and re-usable

Usage & ApplicationsClamping components and connections in cable splice and jointing assemblies; general hose and duct clamping

Product TypeWorm-drive band clamp with captive screw

MaterialStainless steel or steel electroplated for corrosion resistance

Usage & ApplicationsIndoor and outdoor termination of 3-core paper insulated lead covered cable armoured belted or screened

Install TypeHeat shrink with a gas torch; illustrated instructions in every kit

Product TypeHeat shrinkable termination kit for 3-core PILC cable indoor or outdoor

VoltageMedium Voltage

Rated Voltage11 kV (12 kV class) up to 22 kV (24 kV class) 33 kV (36 kV class)

MaterialHeat shrinkable irradiation cross-linked polyolefin sleeves oil barrier sleeves and rain sheds with stress control and sealing mastics

MOQ10000 Kit/Kits

Conductor TypeOther

Conductor ShapeOther

Jacket ColorRed

Product TypeCable Jointing Kit

VoltageHigh Voltage

Insulation MaterialXLPE