Silver Universal Programmer Smartprog2

Universal Programmer SmartProg227554   supported devices from 211 manufacturersSmall, fast and powerful universal programmerDIL40 ZIF socket, devices in DIL package up to 40 pins are supported without adaptersConnector for in-circuit programming (ISP)Connection to PC: USB portUSB 2.0 full speed and USB 1.1 compatibleComfortable and easy to use control program, Windows 98/Me/NT/2000/XP/2003/XPx64/Vista/7 compatibleFree SW update, download from InternetPower supply, cable and software includedApproved by CE laboratory to meet CE requirementsMade in SlovakiaWarranty - 3 years GeneralSmartProg2 is the next member of new generation of Windows 98/ME/NT/2000/XP/2003/XP64/Vista/7 based ELNEC universal programmers. Programmer is built to meet the demands of development labs and field engineers for universal, but portable programmer.SmartProg2 is a small, fast and powerful programmer of all kinds of programmable devices. Using build-in in-circuit serial programming (ISP) connector the programmer is able to program ISP capable chips in-circuit. SmartProg2 isn't only a programmer, but also a static RAMs tester.Provides very competitive price with excellent hardware design for reliable programming. Nice "value for money" in this class.Very fast programming due to high-speed FPGA driven hardware and USB 2.0 full speed port.SmartProg2 interfaces with the IBM compatible PC, portable or desktop personal computers through USB port, what is important for new, LPT-port-less computers (notebooks for example). Hardware40 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.The programmer performs device insertion test (wrong device position in socket) and contact check (poor contact pin-to-socket) before it programs each device. These capabilities, supported by signature-byte check help prevent chip damage due to operator error.SmartProg2 programmer performs programming verification at the marginal level of supply voltage, which, obviously, improves programming yield, and guarantees long data retention.Various socket converters are available to handle device in PLCC, SOIC, SSOP, TSOP, TSSOP, TQFP, QFN (MLF) and other packages. SoftwareProgrammer is driven by an easy-to-use control program with pull-down menus, hot keys and on-line help. Selecting of device is performed by its class, by manufacturer or simply by typing a fragment of vendor name and/or part number.Standard device-related commands (read, blank check, program, verify, erase) are enhanced by some test functions (insertion test, signature-byte check), and some special functions (autoincrement).All known data formats are supported. Automatic file format detection and conversion during loading of file.The rich-featured autoincrement function enables one to assign individual serial numbers to each programmed device - or simply increments a serial number, or the function enables one to read serial numbers or any programmed device identification signatures from a file.The software also provide a many information about programmed device. As a special, the drawing of all available packages are provided. The software provide also explanation of chip labelling (the meaning of prefixes and suffixes at the chips) for each supported chip.The software provide a full information for ISP implementation: Description of ISP connector pins for currently selected chip, recommended target design around in-circuit programmed chip and other necessary information. Technical Specifications Hardware Programmer Two D/A converters for VCCP and VPP, controllable rise and fall time VCCP range 2V-7V/350mA VPP range 2V-25V/200mA USB 2.0/1.1 compatible interface Auto calibration Selftest capability ZIF socket, pindriver 40-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 40-pins Pindriver: 40 TTL pindrivers, specialized GND/VCC/VPP pindriver FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins; level H selectable from 1.8V up to 5V Continuity test: each pin is tested before every programming operation ISP connector 10-pin male type with missinsertion lock 5 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage including) devices. 1x VCCP voltage (range 2V-7V/100mA) (*1) and 1x VPP voltage (range 2V-25V/50mA) programmed chip voltage (VCCP) with both source/sink capability and voltage sense (*1) - the programmer is not capable to supply a target system from VCCP pin. If you have such demand, use please a BeeProg programmer Device Support Programmer, in ZIF socket EPROM: NMOS/CMOS, 27xxx and 27Cxxx series, with 8/16 bit data width, full support of LV series (*1*2) EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data width, full support of LV series (*1*2) Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, with 8/16 bit data width, full support of LV series (*1*2) Serial E(E)PROM: 24Cxxx, 24Fxxx, 25Cxxx, 25Bxxx, 25Dxxx, 59Cxxx, 25Fxxx, 25Pxxx, 25Qxxx, 85xxx, 93Cxxx series, AT88SCxxx, full support for LV series (*1) Configuration (EE)PROM: XCFxxx, 37LVxx, XC17xxxx, EPCxxx, AT17xxx, LV series including NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD U63x series PLD: series: Atmel, AMD-Vantis, Cypress, ICT, Lattice, NS, (*1) Microcontrollers 51 series: 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx, 89LVxxx, 89LSxxx, 89LPxxx, LPC series from Atmel, Atmel W&M, Intel, Philips, SST, Winbond (*1*2) Microcontrollers Atmel AVR: rady AT90Sxxxx, AT90pwm, AT90can, AT90usb, ATtiny, ATmega, (*1*2) Microcontrollers Cypress: CY8Cxxxxx Microcontrollers ELAN: EM78Pxxx Microcontrollers EM Microelectronic: 4 and 8 bit series microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17Cxxx, PIC18xxx, dsPIC series, 8-40 pins (*1*2) microcontrollers Scenix (Ubicom): SXxxx series Microcontrollers Silicon Laboratories(Cygnal): C8051 series Microcontrollers other: ASP, Macronix, Princeton, EXODUS Microelectronic, Goal, Ramtron, Topro, VersaChips, Winbond Programmer, through ISP connector Serial E(E)PROM: IIC series, MW series, SPI series, KEELOQ series, serial data Flash Microcontrollers Atmel AVR: AT89Sxxx, AT90Sxxxx, AT90pwm, AT90can, AT90usb, ATtiny, ATmega, AT89LSxxx, AT89LPxxx Microcontrollers Cypress: CY8C2xxxx Microcontrollers Elan: EM78Pxxx Microcontrollers EM Microelectronic: 4 and 8 bit series Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17xxx, PIC18xxx, dsPIC series Microcontrollers Philips: LPC series Microcontrollers Silicon Laboratories(Cygnal): C8051 series Notes (*1) - Suitable adapters are available for non-DIL packages (*2) - There exist only a few adapters for devices with more than 40 pins. Therefore, please, consider a more powerful programmer (LabProg+, BeeProg, JetProg), if you need to program devices with more than 40 pins For all supported devices see actual Device list I.C. Tester Static RAM: 6116- 624000 Programming speed Device Operation Mode Time 27C010 programming and verify in ZIF 28 sec. AT29C040A programming and verify in ZIF 32 sec. AM29F040 programming and verify in ZIF 62 sec. PIC16C67 programming and verify in ZIF 10 sec. PIC18F452 programming and verify in ZIF 7 sec. AT89C52 programming and verify in ZIF 16 sec. PIC16F876A programming and verify ISP 5 sec. PIC12C508 programming and verify ISP 3 sec. Conditions: P4, 2.4 GHz, USB 2.0 high speed, Windows XP.The programming times are valid for 2.11 version of software, the improvement is in progress.