Industrial Waterproofing Solution In Indore

ComplianceIS 2975

Coverage100 m²/day

Drying Time24 hours

FeaturesLeak prevention Durable Cost-effective Long-lasting Expert application

MaterialPolymer membrane

Thickness2-5 mm

MOQ1 Kilograms/Kilograms

MaterialAcrylic water base

UsageConstruction

GradeA

Purity98%

ApplicationIndustrial

Physical StateLiquid

Elongation5%

FeaturesWater Resistance Structural Integrity Durable Long Lasting Easy Application

MaterialPolymeric Membrane

Temperature Range-20°C to 60°C

Tensile Strength10 MPa

Thickness2 mm

MOQ1 Piece/Pieces

Product TypeBitumen Membrane

SizeDifferent Size Available

UsageIndustrial

FeatureWaterproof

MOQ10 Liter/Liters

GradeHigh

Place of OriginIndia

SolubilitySoluble in water

AdvantageHighly durable excellent adhesion ecoaEUR'friendly easy application

Product TypeWaterproofing Compound

Purity99

MOQ1 Unit/Units

ColorGrey

TypeWaterproof Membrane

MaterialMembrane

ApplicationBrush/Roller

ColorGray

Coverage100 sq ft/gallon

Drying Time4 hours

FeaturesWaterproofing Durable Long-lasting Cost-effective Reliable Protection

MaterialPolymer-based

Application MethodSpray/Brush

ComplianceASTM D412

Coverage Area100m²/day

FeaturesLeak prevention Long-lasting Cost-effective Quick application Expert installation

MaterialBituminous

Primary ColorGray

Application MethodTorch-on

ComplianceIS 1537

FeaturesLeak prevention Durable Cost-effective Reliable Long-lasting Watertight

MaterialBituminous

Thickness1-3 mm

UsageRoofs tanks and building waterproofing

MOQ100 Kilograms/Kilograms

SurfaceSmooth

StateLiquid Coating

FeatureWaterproof

Main MaterialEpoxy

Application MethodBrush

StyleLiquid Coating

ColorOrange

Coverage100 sq ft/liter

Density1.1 g/ml

Drying Time4-6 Hours

FeaturesWaterproofs surfaces Durable coating Easy application Long-lasting Cost effective Superior protection

MaterialChemical

MOQ5 Pack/Packs

ApplicationHydro lastik is applied with a fibre type brush or by trowel when a smooth finish is required. For large areas Hydro Lastik can also be sprayed being the recommended nozzle size 3-4 mm and spraying pressure between 3.5 and 5.0 bar. When sprayed it is recommended to finish the fresh coat with a trowel to make sure that the whole surface is covered completely.Applytwo coats using 1 aEUR" 1.5 kg/mA2 Hydro lastik per coat and allow a minimum of 16 hours and a maximum of 3 days between applications. Prior to application thoroughly wash down and saturate the surface but do not leave free standing water. Thickness per layer should be 1 mm approximately thereby being important to avoid very thin application or on the opposite a much thicker one. In those areas such as fissures concrete joints and active cracks once repaired and sealed. Place the mesh on a first coat of Hydro lastik with at least 20 cm wide of strip and then apply a second coat of Hydro Lastik. Application conditions Optimum application temperature is between 10EsC to 25EsC. Do not apply below 5EsC or if lower temperatures are expected within the following 24 hours after application. Do not apply on frozen surfaces or if rain is expected 24 hours after application. Protect against quick drying by winds and direct sunlight with high temperatures by fog spraying with water for two hours after application.Curing time required to put the product into service or to immerse it in water will depend on temperature and relative humidity conditions on site. Conditions in the range of 20EsC and 50% R.H will require a minimum of 14 days to ensure that the product has cured enough to be in permanent contact with water. Applications made at lower temperatures or sites without ventilation will require longer curing periods. After curing wash the surface of Hydro Lastik with water before putting into service in permanent contact with water.

Colorwhite

Physical StatePowder