Industrial Waterproofing Solution In Vapi

ColorOrange

Coverage100 sq ft/liter

Density1.1 g/ml

Drying Time4-6 Hours

FeaturesWaterproofs surfaces Durable coating Easy application Long-lasting Cost effective Superior protection

MaterialChemical

MOQ5 Pack/Packs

ApplicationHydro lastik is applied with a fibre type brush or by trowel when a smooth finish is required. For large areas Hydro Lastik can also be sprayed being the recommended nozzle size 3-4 mm and spraying pressure between 3.5 and 5.0 bar. When sprayed it is recommended to finish the fresh coat with a trowel to make sure that the whole surface is covered completely.Applytwo coats using 1 aEUR" 1.5 kg/mA2 Hydro lastik per coat and allow a minimum of 16 hours and a maximum of 3 days between applications. Prior to application thoroughly wash down and saturate the surface but do not leave free standing water. Thickness per layer should be 1 mm approximately thereby being important to avoid very thin application or on the opposite a much thicker one. In those areas such as fissures concrete joints and active cracks once repaired and sealed. Place the mesh on a first coat of Hydro lastik with at least 20 cm wide of strip and then apply a second coat of Hydro Lastik. Application conditions Optimum application temperature is between 10EsC to 25EsC. Do not apply below 5EsC or if lower temperatures are expected within the following 24 hours after application. Do not apply on frozen surfaces or if rain is expected 24 hours after application. Protect against quick drying by winds and direct sunlight with high temperatures by fog spraying with water for two hours after application.Curing time required to put the product into service or to immerse it in water will depend on temperature and relative humidity conditions on site. Conditions in the range of 20EsC and 50% R.H will require a minimum of 14 days to ensure that the product has cured enough to be in permanent contact with water. Applications made at lower temperatures or sites without ventilation will require longer curing periods. After curing wash the surface of Hydro Lastik with water before putting into service in permanent contact with water.

Colorwhite

Physical StatePowder

Active IngredientOrgano Silane

Application MethodSpray/Brush/Roller

ColorClear

FeaturesWaterproofing Long-lasting Easy application UV resistant Fungus resistant Cost effective Deep penetration Thermal stable

Product TypeWaterproofing solution

Shelf Life2 years

ApplicationSpray/Flood/Injection

BaseNano-technology

Coverage24-100m2

Dilution Ratio1:15-20

Drying Time3-7 days

FeaturesDeep penetration Long-lasting UV resistant Seepage proof Easy application Cost-effective Abrasion resistant Water repellent

MOQ10 Roll/Rolls

ColorWhite

Size1x50 Meter

Product TypeWaterproofing Fiberglass Mesh

MaterialFiberglass Mesh

ApplicationWaterproofing

ComplianceASTM D4492

FeaturesWaterproofing Leak prevention Durable Long-lasting Cost-effective

MaterialBitumen

Temperature Range-20°C to 80°C

Tensile Strength10 MPa

Thickness2-3 mm

ApplicationBrush/Roller

ColorOrange

Coverage100m2

FeaturesWaterproofing Protection Long-lasting Cost-effective

MaterialPolymer

Thickness2mm

Coverage AreaVariable

FeaturesLeak prevention Moisture control Durable finish Cost-effective Expert service Long-lasting Improved structure

Materials UsedHigh-grade

MethodologyVarious

Project DurationVariable

Service TypeWaterproofing

MOQ200 Kilograms/Kilograms

TypeAdmixture

Other NamesMcon Lwp

Water Content<1%

ColorYellow

GradeIndustrial Grade

Purity100%

MOQ1 Kilograms/Kilograms

Product TypeSBR Waterproofing Material

ColorBlue

MOQ1000 Square Foot/Square Foots

Supply Ability1000 Per Day

Delivery Time1 Week

Main Domestic MarketAll India

MOQ30 Kilograms/Kilograms

StrengthHigh

Application MethodRoller

TextureSmooth

Surface FinishSmooth

StorageRoom Temperature

Weather ResistanceYes

MOQ1 Piece/Pieces

CoatingAnodized Coating

MethodSubtractive Manufacturing

ShapeRectangular

HardnessYes

CNCYes

UseIndustrial CNC Control Systems

MOQ100 Kilogram Kilograms/Kilograms

PurityHigh

Physical FormLiquid

GradeIndustrial

TypeLatex Waterproofing Coating

Application MethodBrush

ComplianceIS 2630

Drying Time24 hours

FeaturesLeak prevention Long-lasting Waterproofing Cost-effective Expert team

MaterialPolymer

Surface AreaVariable