Industrial Waterproofing Solution In Delhi

MaterialWaterproofing membrane

Application MethodProfessional installation

Warranty1 year

Project SizeVariable

Preparation Time2-3 days

Installation Time1-2 days

Product TypeMembrane

Primary ColorWhite

MaterialPolymer

Thickness Range1-3 mm

Tensile Strength10 MPa

Elongation200%

MOQ20 Kilograms/Kilograms

TypeWaterproofing Coating Solution

MOQ20 Bag/Bags

FeatureWaterproof

Application MethodBrush

MOQ1 Pack/Packs

Physical FormPowder

GradeIndustrial Grade

MaterialPolymer membrane

Thickness2-5 mm

Coverage100 m²/day

Warranty5 years

ComplianceIS 2975

UsageIndustrial building waterproofing roof and terrace

MOQ100 Kilograms/Kilograms

SurfaceSmooth

StateLiquid Coating

FeatureWaterproof

Main MaterialEpoxy

Application MethodBrush

StyleLiquid Coating

ColorOrange

MaterialChemical

Packaging5 Liter Can

Coverage100 sq ft/liter

Density1.1 g/ml

Drying Time4-6 Hours

MOQ5 Pack/Packs

ApplicationHydro lastik is applied with a fibre type brush or by trowel when a smooth finish is required. For large areas Hydro Lastik can also be sprayed being the recommended nozzle size 3-4 mm and spraying pressure between 3.5 and 5.0 bar. When sprayed it is recommended to finish the fresh coat with a trowel to make sure that the whole surface is covered completely.Applytwo coats using 1 aEUR" 1.5 kg/mA2 Hydro lastik per coat and allow a minimum of 16 hours and a maximum of 3 days between applications. Prior to application thoroughly wash down and saturate the surface but do not leave free standing water. Thickness per layer should be 1 mm approximately thereby being important to avoid very thin application or on the opposite a much thicker one. In those areas such as fissures concrete joints and active cracks once repaired and sealed. Place the mesh on a first coat of Hydro lastik with at least 20 cm wide of strip and then apply a second coat of Hydro Lastik. Application conditions Optimum application temperature is between 10EsC to 25EsC. Do not apply below 5EsC or if lower temperatures are expected within the following 24 hours after application. Do not apply on frozen surfaces or if rain is expected 24 hours after application. Protect against quick drying by winds and direct sunlight with high temperatures by fog spraying with water for two hours after application.Curing time required to put the product into service or to immerse it in water will depend on temperature and relative humidity conditions on site. Conditions in the range of 20EsC and 50% R.H will require a minimum of 14 days to ensure that the product has cured enough to be in permanent contact with water. Applications made at lower temperatures or sites without ventilation will require longer curing periods. After curing wash the surface of Hydro Lastik with water before putting into service in permanent contact with water.

Colorwhite

Physical StatePowder

MOQ1 Kilograms/Kilograms

MaterialAcrylic water base

UsageConstruction

GradeA

Purity98%

ApplicationIndustrial

Physical StateLiquid

MaterialPolymeric Membrane

Thickness2 mm

Width1 Meter

Tensile Strength10 MPa

Elongation5%

Temperature Range-20°C to 60°C

MOQ1 Piece/Pieces

Product TypeBitumen Membrane

SizeDifferent Size Available

UsageIndustrial

FeatureWaterproof

MOQ10 Liter/Liters

GradeHigh

Place of OriginIndia

SolubilitySoluble in water

AdvantageHighly durable excellent adhesion ecoaEUR'friendly easy application

Product TypeWaterproofing Compound

Purity99

MOQ1 Unit/Units

ColorGrey

TypeWaterproof Membrane

MaterialMembrane

MaterialPolymer-based

ColorGray

Coverage100 sq ft/gallon

Drying Time4 hours

ApplicationBrush/Roller

Surface PrepClean surface