We are working in this field since 1960 and have satisfied customers all over India and abroad. We assure you of our best quality and products.

Frame Construction: The FRAME is strong, robust and of welded construction. This frame is fabricated from quality steel, which is stress relieved before machining. In the LHPB Series the frame is floor type and monoblock in construction. With floor type construction bottom beam is welded to the main table. Crowing is provided in the removable table to compensate for deflections. Above the LHPB 300 the bottom beam is removable.

Hydraulic Group: Another unique feature of Lamba P+S Press brakes is its well designed and proven hydraulic group having the following features:-

* Monoblock construction with the minimum of pipe fittings and valves.
* Use of quality seals and good surface finish on moving parts.
* Low noise level pump keeps noise level well bellow 70dB.
* Provision of a built in safety valve ensures safety against overload.
* Provides infinitely adjustable pressure and full pressing capacity over the entire bending operation.

The Control Station: The Control station is a compact unit located conveniently to provide ease in use. All the necessary controls and optional controls are provided on this control station. The movable foot switch provides flexibility and ease in operation. An additional foot switch is provided for returning ram at any position in the stroke.

Back Gauge Options: Back gauge is provided as an optional attachment. A wide range of options for the Back Gauge are available.

1. Simple micro metric Back gauge fitted on the table with manual adjustment.
2. Back gauge fitted on uprights with front readout in either manual or motorised versions.

Versatility for Punching, Perforating, Pressing etc.: Longer stroke length, good stripping force allows punching to be done up to 60% capacity. With full tonnage along entire stoke length, tools can be staggered to punch-perforate goes requiring bigger combined capacity.

Standard features-accessories for basic model:
* Ram travel repeatable with in + 0.03mm for consistent bends for interchangeable output.
* Ram travel is referenced from bed to avoid side frame deflections affecting stroke accuracy.
* Rugged structure from ultra tested is 2062 grade B plates, rigidity conforming to international standards.
* Hydraulic, electrics of internationally reputed brands for consistent performance and reliable operation.
* Facility to adjust tonnage for thin or segmented too lings or when bending special materials.
* Front sheet supports with T-slots, in-laid scale and stops to gauge the sheet from front with clear view.
* Most hydraulic parts rated for 310 bar but working pressure only 160 bar for long life, reliable operation.
* Pivots with permanently lubricated bearings or hardened parts lubricated by central hand pump.
* Cylinders of ultra-tested seamless honed tubes, hard chrome-plated pistons, dual seals (Teflon ring plus set of chevron pickings) for extra reliability.
* 3-speed bending cycles for faster output yet slow smooth bending with minimal shock loads.
* Movable-control station with majority controls, emergency stop, up-down foot-switch controls.
* Inch cycle mode for set-up and one-off jobs. Single cycle modes for repeat cycles, production runs.
* Main cylinders seals can be easily replaced without requiring crane or dismantling the ram.
* Hydraulic power gives silent working, better safety against overload, instant stoppage-reversal of ram.
* One set of hardened standard punch, multi-vee die block (not covered in warranty).

Note: All dimensions are approximate and illustrations are not binding to detail. We always endeavor to improve to improve designs from time to time with a view to solve difficult problems for handling jobs in a modern sheet metal workshops.

See more Products of Hydraulic Press Brake

Model: LHPB5 : 50 ton
Model: LHPB8 : 80 ton
Model: LHPB12 : 120 ton
Model: LHPB16 : 160 ton
Model: LHPB20 : 200 ton
Model: LHPB25 : 250 ton
Model: LHPB35 : 350 ton

Kindly, mail us for more information.