Blind Flanges BLIND FLANGES are used to blank off the ends of piping, valves and pressure vessel opening. From the standpoint of internal pressure and bolt loading, blind flanges, particularly in the larger sizes, are the most highly stressed of all flange types; however, since the maximum stresses in a blind flange are bending stresses at the center, they can safely be permitted to be higher than in other types of flanges. Dimensions 300# DIM & Weight

Stainless Steel Buttweld Fitting Stainless Steel : ASTM A 403 Grade : WPS/WPW 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H Carbon Steel : ASTM A 234 Grade :. WPB/WPBW, (IBR/Non IBR) Alloy Steel : ASTM A 234, Gr. WP1, WP11, WP22, WP5, WP9, WP91, (IBR/Non IBR) Nickel Alloys : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy 904 Copper Alloys : Aluminium, Copper, Brass & Gunmetal Types : Elbow, Tee, Reducer, Return Bends, Stub-Ends, Cap, Colla, Cross, Insert, etc. Size : 1/8"NB TO 48"NB. (seamless & welded)

Carbon Steel Buttweld Fitting Stainless Steel : ASTM A 403 Grade : WPS/WPW 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H Carbon Steel : ASTM A 234 Grade :. WPB/WPBW, (IBR/Non IBR) Alloy Steel : ASTM A 234, Gr. WP1, WP11, WP22, WP5, WP9, WP91, (IBR/Non IBR) Nickel Alloys : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy 904 Copper Alloys : Aluminium, Copper, Brass & Gunmetal Types : Elbow, Tee, Reducer, Return Bends, Stub-Ends, Cap, Colla, Cross, Insert, etc. Size : 1/8"NB TO 48"NB. (seamless & welded)

Stainless Steel Flanges Stainless Steel : ASTM A 182, A 240 Grade : F 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H Carbon Steel : ASTM A 105, ASTM A 181 Alloy Steel : ASTM A 182, GR F1, F11, F22, F5, F9, F91 Nickel Alloys : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy 904 Copper Alloys : Aluminium, Copper, Brass & Gunmetal Types : Weldneck, Slipon, Blind, Socket Weld, Lap Joint, Spectacles, Ring joint, Orifcase, Long Weldneck, Deck Flange, etc. Size : 1/8" NB TO 48"NB. Class : 150#, 300#,400 #,600#,900#,

Lap Joint Flanges LAP JOINT FLANGES are primarily employed with lap joint stubs, the combined initial cost of the two items being approximately one-third higher than that of comparable welding neck flanges. Their pressure-holding ability is little, if any, better than that of slip-on flanges and the fatigue life of the assembly is only one-tenth that of welding neck flanges. The chief use of lap joint flanges in carbon or low alloy steel piping systems is in services necessitating frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt ho

Forged Pipe Fittings Stainless Steel : ASTM A 182 Grade : F 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H Carbon Steel : ASTM A 105, A187, (IBR & NON IBR) Alloy Steel : ASTM A 182, Grade F1, F11, F22, F5, F9, F91 (IBR & NON IBR) Nickel Alloys : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy 904 TYPES : Elbow, Tee, Union, Cross, Coupling, Cap, Bushing, Plug, Swage Nipple, Welding Boss, Hexagon Nipple, Barrel Nipple, Welding Nipple, Parraler Nipple, Street Elbow, Hexagon Nut, Hose Nipple, Bend, Adapter, Insert, Weldolet,

Orifice Flanges ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding neck and slip-on flanges except for the provision of radial, tapped holes in the flange ring for meter connections and additional bolts to act as jack screws to facilitate separating the flanges for inspection or replacement of the orifice plate. In choosing the type of orifice flange, the considerations affecting the choice of welding neck and slip-on standard flanges apply with equal force. Dimensions 25

Slip On Flanges SLIP-ON FLANGES continue to be preferred to welding neck flanges by many users on account of their initially lower cost, the reduced accuracy required in cutting the pipe to length, and the somewhat greater ease of alignment of the assembly; however their final installed cost is probably not much, if any, less than that of welding neck flanges. Their calculated strength under internal pressure is approximately two-thirds that of welding neck flanges, and their life under fatigue is about one-third that of the latter. For these reasons, slip-on flanges are limited to sizes

Threaded Flanges THREADED FLANGES are confined to special applications. Their chief merit lies in the fact that they can be assembled without welding this explains their use in extremely high pressure services, particularly at or near atmospheric temperature, where alloy steel is essential for strength and where the necessary post weld heat treatment is impractical. Threaded flanges are unsuited for conditions involving temperature or bending stresses of any magnitude, particularly under cyclic conditions, where leakage through the threads may occur in relatively few cycles of heating or

Weld Neck Flanges WELDING NECK FLANGES are distinguished from other types by their long tapered hub and gentle transition of thickness in the region of the butt weld joining them to the pipe. The long tapered hub provides an important reinforcement of the flange proper from the standpoint of strength and resistance to dishing. The smooth transition from flange thickness to pipe wall thickness effected by the taper is extremely beneficial under conditions of repeated bending, caused by line expansion or other variable forces and produces an endurance strength of welding neck flanged assemb

Stainless Steel: ASTM A403 WP 304/ 304L/ 304H/316/ 316L/ 317/ 317L/ 321/ 310/ 347/ 904L etc. Carbon Steel: ASTM A234 WPB / A420 WPL3/ A420 WPL6/ MSS-SP-75 WPHY 42/46/52 /56/60/65/70 Alloy Steel: ASTM A234 WP1/ WP5/ WP9/ WP11/ Wp22/ WP91 etc. Others : Monel, Nickel, Inconel, Hastalloy, Copper, Brass, Bronze, Titanium, Tantalum, Bismuth, Aluminium, High Speed Steel, Zinc, Lead, Etc. Types : Elbo

Stainless Steel: ASTM A182F304/304L/304H/ 316/ 316L/ 317/ 317L/ 321/ 310/ 347/ 904Letc. Carbon Steel: ASTM A105/ A694/ F42/46/52/56/60/65/70/ A350 LF3/A350 LF2, etc. Alloy Steel: ASTM A182 F1/ F5/ F9/ F11/ F22/ F91 etc. Others : Monel, Nickel, Inconel, Hastalloy, Copper, Brass, Bronze, Titanium, Tantalum, Bismuth, Aluminium, High Speed Steel, Zinc, Lead, Etc. Types : Weldneck, Slipon, Blind, S

We supply assortment of screwed and forged fittings available in various shapes and sizes. Utilization of premium grade of raw material in manufacturing process ensures our range meet the quality in terms of national and international standard. Our fittings come in the following types including elbow, tee, union, cross, coupling, cap, bushing , plug, swage nipple, welding boss, hexagon nipple, bar

We export comprehensive range of flanges that is manufactured from qualitative grade of raw material such as stainless steel, carbon steel, alloy steel and several others. Our gamut of flanges is free of imperfection and compactly designed to offer superior functionality.