LOE Series LOE 200 & 300 series bearing housings are suitable for spherical roller bearings with cylindrical bore of series 22200 CC & 22300 CC high speed bearing application with oil lubrication. The housings are horizontally split supplied with two labyrinth covers sealed with two labyrinth rings. The housings are equipped with breather plug, drain plug, oil pick-up ring, one oil level indicator. Water cooling coil for sump oil can be provided on order. For through shaft, both ends are open and for shaft terminating inside the housing, an end cover is provided to close the end.

Bearing Sleeves MASTA Adapter and withdrawal BEARING SLEEVES are available in mm and inch size complete with lock nuts and looking washers. The SLEEVES are slotted and heaving external taper of 1:12 to suiet corponding bearing inside shaft hole taper.

PDN Series VRA and PDN series bearing housings are mono-bearing housing accommodating two bearings with unsplit design which can either be supplied in Cast Iron or Cast steel materials. The bearing housings are suitable for grease lubrication and the shaft holes are sealed with felt seals/ strips. The width of the bearing seats enables floating arrangements. Deep groove-bearings of series 6200 and 6300 and / or cylindrical roller bearings of NJ2 and NJ3-series can be accommodated.

S Series SAF or SDAF type bearing housings are horizontally split type in construction and are available in Cast Iron, Cast steel or S.G. Iron material as per order. They are suitable to withstand heavier and shock loads due to its robust construction. For efficient seating and preventing foreign particles to enter in to the bearing housings, triple or double seal type labyrinth rings are provided. For mounting the plummer blocks on the foundation, two or four elongated bolt holes are provided. For four bolt holes, plummer block designation is prefixed with "F" e.g. FSAF 520.

SD Series SD series Plummer blocks are made of Grey Cast Iron Grade FG 200 of IS : 210, which can be made from SG Iron (SDD) or Cast steel Castings (SDT) also for heavier loads on order SD series plummer blocks are suitable for spherical roller bearings of series 231 K with adapter sleeves for shaft dia 150 mm to 300 mm, and same are designated as SD 31. Plummer blocks suitable for bearings series 230 are designated as SD 30.similarly SD 500 and SD 600 series plummer blocks are suitable for 22200 CK and 22300 CK series bearings respectively. These plummer blocks are either supplied wit

SDG Series SDG housings are made of Grey Cast Iron as per IS : 210 (SDGC Type) which can also be made from S.G.Iron (SDGD Type) or Cast Steel Castings (SDGS Type) for heavier load application. These housings are suitable for Grease Lubrication and for spherical Roller Bearings with adapter sleeve or withdrawal sleeves mountings on bearings with cylinderical bore in 22200, 23200, 23000, 23100 & 24100 Bearing series. These housings are split type and incorporate cover at one side which is inserted in a groove of the housing bore. Labyrinth Seals are provided on each side for through shaft

SN Series "MASTA" SN Series horizontally split type Plummer Blocks are ideally suitable for moderate loads, speeds and relatively clean and temperate environment. The width of bearing seat in the SN series plummer blocks is such that it gives bearings axial freedom. A locating bearing is positioned by the insertion of one or two locating rings as the case may be for its axial location. SN Series plummer Blocks are suitable for Grease lubrication. Felt strips and Grease Nipples can be supplied along with plummer blocks on order. For dirty environment SN Series plummer blocks can

SNA Series "MASTA" SNA series horizontally split plummer blocks (bearing housings) are completely interchangeable with earlier SN type plummer blocks, concerning mainly to its center height, foundation bolt centres. Same bearing housings can be used for 500 and 600 series bearings having equal bearing outside diameter by changing its shaft seals, e.g. SNA 506 plummer blocks can be used as SNA 605 also where bearing O.D of 1206 K and 1305 K are equal e.g., 52 mm. Similarly same plummer blocks can be used for bearing with tapered bore mounted with adapter sleeve or bearing with (stra

SNH Series "MASTA" SNH series plummer blocks are also horizontally split and are fully interchangeable with those of earlier SN and SNA series plummer blocks. All features of standard and special shaft seals, interchangeability with 500 and 600 series for bearing with tapered bore and adapter mounting or with (straight) cylindrical bore etc. are available in SNH series plummer blocks also. Its more favourable cross section and improved design have resulted into greater strength as compound to SN or SNA series Plummer Blocks. SNH plummer blocks have dowel pins at its mating surfac

SNL Series SNL Plummer Blocks housings are suitable for self aligning ball bearings, spherical roller bearings and CARB bearings for shaft dia 20 to 160 mm. These housings are split type with 2 elliptical holes in housing base and suitable for grease or oil lubrication. For Grease lubrication variety of seals such as felt seals (TC Type), Labyrinth Seals (TS Type), Double Lip Seals (TG Type) or Taconite Seals (ND Type) can be used. For oil lubrication special type of seal (TURU type) can be used. Principal dimensions are identical to SNA/SNH type housings and are interchangeable. SNL hous

SOFN Series SOFN BEARING HOUSINGS:Oil lubricated cast steel bearing housing are suitable for sphearical roller bearings running high speed and high operating temperature. SOFN 200 and 300 series bearing housings are suitable for spherical roller bearings with tepered bore and adapter sleeve mounting. SOFN bearing housing are comprising of main body consisting of top and bottom housings, with labyrinth covers and collars, oil splash ring for splash lubricating system or oil inlet and outlet pipe fittings on either side of housings in the labyrinth covers for oil circulatory system. Oil

THD SPA Series THDS / SPA bearing housings are take up housings made of Cast Steel. However they can also be manufactured in Cast Iron (THDC) or in S.G. iron (THDD). The housings having two slots suitable tor closed rail or open rail guides on the conveyor frame and the yoke establishes the connection with the tensioning block. These housings are also supplied either with an end cover for the end shaft or both ends open for through shaft.

Triangular Flanged Series Flanged housings in TRIANGULAR type from shaft dia 20mm to 60 mm & SQUARE type from shaft dia 65mm to 100mm are intended for use with self aligning ball bearings of series 12K, 22K and SRB 222K series on adapter sleeve mountings. These housings are available for located or non located bearings and are made up of Cast Iron. Felt Seals are used for sealing of shaft and are supplied with end cover as A type & for through shaft as "B" type. They are available as 7225(00) & F 500 series along with I-1200 (00) series suitable for self aligning bal

SOFN Series SOFN BEARING HOUSINGS:Oil lubricated cast steel bearing housing are suitable for spherical roller bearings running high speed and high operating temperature. SOFN 200 and 300 series bearing housings are suitable for spherical roller bearings with tapered bore and adapter sleeve mounting. SOFN bearing housing are comprising of main body consisting of top and bottom housings, with labyrinth covers and collars, oil splash ring for splash lubricating system or oil inlet and outlet pipe fittings on either side of housings in the labyrinth covers for oil circulatory system. Oil l

SAF or SDAF type bearing housings are horizontally split type in construction and are available in Cast Iron, Cast steel or S.G. Iron material as per order. They are suitable to withstand heavier and shock loads due to its robust construction. For efficient seating and preventing foreign particles to enter in to the bearing housings, triple or double seal type labyrinth rings are provided. For mo

MASTA" SNA series horizontally split plummer blocks (bearing housings) are completely interchangeable with earlier SN type plummer blocks, concerning mainly to its center height, foundation bolt centres. Same bearing housings can be used for 500 and 600 series bearings having equal bearing outside diameter by changing its shaft seals, e.g. SNA 506 plummer blocks can be used as SNA 605 also where b

"MASTA" SNH series plummer blocks are also horizontally split and are fully interchangeable with those of earlier SN and SNA series plummer blocks. All features of standard and special shaft seals, interchangeability with 500 and 600 series for bearing with tapered bore and adapter mounting or with (straight) cylindrical bore etc. are available in SNH series plummer blocks also. Its more favour

MASTA" SN Series horizontally split type Plummer Blocks are ideally suitable for moderate loads, speeds and relatively clean and temperate environment. The width of bearing seat in the SN series plummer blocks is such that it gives bearings axial freedom. A locating bearing is positioned by the insertion of one or two locating rings as the case may be for its axial location. SN Series plummer Bloc

One piece housing with side covers, labyrinth rings and split spring rings or with side covers and oil seals is the main feature of BND / SBDS series plummer blocks. These plummer blocks are having four bolt slots for foundation and two grease nipples for lubrication. Design A: For shaft terminating inside the housing. End cover seals one end of the housing. Design B: Both ends are open for

SNL Plummer Blocks housings are suitable for self aligning ball bearings, spherical roller bearings and CARB bearings for shaft dia 20 to 160 mm. These housings are split type with 2 elliptical holes in housing base and suitable for grease or oil lubrication. For Grease lubrication variety of seals such as felt seals (TC Type), Labyrinth Seals (TS Type), Double Lip Seals (TG Type) or Taconite Seal